The Powercreter Elite 30 is a concrete pump designed specifically for mid-range, multi-duty applications and ideal for construction projects such as foundations, pools, pressure grouting, and rockscaping. The new pump also features a swing-tube design providing smooth concrete flow and fast switchover to minimize surge and pulsation. Visit Booth C-5201.

Write In 507 — Or Reply Online

Allmand's 8435 and 8435 HST four-wheel-drive compact utility tractors are ideal in a wide array of applications including landscape, agriculture, construction, and rental. The 8435 features a synchro-shuttle shift transmission allowing forward and reverse operation and multiple gear range selections are available to manage a variety of implement applications. The 8435 HST features a hydrostatic transmission providing variable speed selection with simple foot-pedal control, eliminating the need for a clutch; cruise control maintains a set speed for extended periods without foot-pedal pressure and automatically disengages when the brake is applied. Both models are powered by a 36-horsepower Mitsubishi S4L2 diesel engine; feature hydraulic power steering; has mechanical four-wheel drive and a differential lock system locking the rear wheels together to maximize traction in difficult conditions; and come equipped with category one, three-point-hitch systems with draft control and standard rear auxiliary hydraulics. Visit Booth G-320.

Write In 274 — Or Reply Online

Among the products on exhibit in electronic instruments and electric motors are dashboard instrument clusters; electronically commutated motors and blowers and magnetically coupled pumps; permanent magnet and wound field motors; and industry battery chargers and contactors. The Universal Instrument Panel is a fully digital, multiplexed dashboard instrument solution for trucks, agricultural/construction and other vehicles and the Rotron DR 757 regenerative blower was developed as a drop-in replacement for its DR 707 regenerative blower used in concrete production. An extensive line of permanent magnet and wound field motors in diameters ranging from 3.3 inches to 13 inches and the Prestolite Power & Switch offers a range of industrial charging solutions from its LTD® ferroresonant charger to its full-featured ULTRA MAXX® SR interactive charger. Visit Booth S-11033.

Write In 508 — Or Reply Online

The HG 7000 hydraulic breaker attachment is the largest breaker in the Atlas Copco line. With a service weight of more than 13 tons, it is used for primary and secondary quarry breaking, demolition, tunneling, trenching, and foundation work. Accepting a maximum hydraulic flow of 119 gallons per minute at 2,610 pounds per square inch of pressure, the HB 7000 delivers an impact rate of up to 450 beats per minute. The attachment comes standard with AutoControl, a monitoring system that allows the hammer to adapt its frequency and power output to match operating conditions. The Start Select system allows start-up and shut-off to be adjusted to fit jobsite conditions and an energy recovery system prevents damage from piston recoil on hard materials. The VibroSilenced damping system reduces excess vibration and noise; DustProtector II protects the inner mechanism from dust damage; and ContiLube® II is an automatic lubrication system mounted directly on the hammer. Visit Booth C-5773.

Write In 426 — Or Reply Online

Bacou-Dalloz, designer, manufacturer and seller of personal protective equipment will exhibit their latest product offerings from Uvex, Willson & Fend-all (eye/head protection) including Harley-Davidson Safety Eyewear, Optrel (welding), Howard Leight and Bilsom (hearing protection), Miller Fall Protection, Willson & Survivair (respiratory protection), Perfect Fit (hand protection), and Biosystems (gas detection). Visit Booth C-6829.

Write In 343 — Or Reply Online

Bernard showcases its welding products including Centerfire™ of MIG welding consumables and Bernard Q-Gun line of MIG guns. Centerfire's contact tips (without threads) "Drop-In" the gas diffuser and lock in place by tightening the nozzle. Changing contact tips do not require tools and are easy to replace after burn back. When coupled with the correct nozzle, tips stay fixed at 1/4-inch or 1/8-inch recess, flush or 1/8-inch stick-out. Their large diameter tip bases and tapered seats increase electrical conductivity and heat transfer and hand-tightened nozzles come with built-in spatter shields protecting gas diffusers and facilitating smoother gas flow. The Bernard Q-Guns minimize welding downtime. In 150-, 200-, 300-, 400-, 500-, and 600-amp models, they provide amperage ratings at 100-percent duty cycle with CO2 gas. A patent-pending straight handle torch offers improved ergonomics; additional trigger and switch options allow the choice between locking trigger, dual pull trigger, dual schedule switch, and trigger extension. Visit Booth G-244.

Write In 509 — Or Reply Online

Timberline Office by Best Software, a suite of integrated financial and operations software for construction and real estate professionals, is highlighted by several new and upcoming features. Now available, change management is a new Project Management feature that provides a simple, integrated solution for the entire change management process, from pricing, tracking, soliciting quotes, and issuing change order requests. Plus, Timberline Office Desktop provides a customizable start page for individual user access to reports, applications and features that are most important in their daily line of work. And, scheduled for release in the first half of 2005, Timberline Office Document Management is a fully integrated system that enables users to automatically index, archive, retrieve, and distribute all electronic and paper-based documents, based on document type or detailed page content. Document Management can work stand-alone, or integrate seamlessly with Timberline Office Accounting, for document indexing and instant document retrieval. Visit Booth S-17015.

Write In 573 — Or Reply Online

BID2WIN 2005 is a Windows-based construction estimating and bidding application built on Microsoft.NET and SQL Server technology. It provides a level of power, performance and flexibility and enhances estimating and bidding through standardization, improved accuracy and efficiency, and integration with other project management solutions. The software stores all cost data in one central database, guaranteeing everyone uses the same up-to-date data when working in estimates. Features include: globally edit materials, labor, equipment, and crews during the actual costing process; fax subcontractor and vendor/materials RFQs in seconds and automatically distribute selected bids directly into an estimate; utilize the power of Microsoft Excel for unlimited costing flexibility; and convert the entire bid from metric to imperial with just a single click. BID2WIN 2005 is a core component of Bidding Intelligence™, a business solution that combines the real-time control of estimate and bid data with subcontractor and vendor collaboration and the ability to generate detailed analysis of a company's historical bidding activity. Visit Booth S-17318.

Write In 510 — Or Reply Online

Bil-Jax Inc. introduces the 36/32T Telescopic Aerial Work Platform. The trailer-mounted boom lift provides 42 feet of working height; 32 feet of outreach; and features an automatic, self-leveling hydraulic outrigger system that allows for setup in three seconds when all four outriggers are deployed simultaneously. The outriggers' leveling capability is 12 degrees and feature 12-inch-diameter non-marking footpads. Available with either 24v DC battery power or Honda gasoline engine, other features include a two-person platform with rated load capacity of 440 pounds; 360-degree continuous turntable rotation; hydraulic surge brakes; forklift pockets; outrigger interlocks; and a 110v GFI duplex outlet within the platform. The 36/32T can be operated from either the platform or ground control station. A display panel with control buttons easily identifies functions and its boom design consists of one primary boom arm containing a telescopic section. The 36/32T can be towed behind vehicles with adequate towing capacity and a Class 3 hitch with maximum tow speed rating of 60 miles per hour. Visit Booth C-4525.

Write In 511 — Or Reply Online

Bobcat Company has expanded its compact track loader line of products with the introduction of the T140 which complements the four-track loaders already manufactured by the company. The new small-frame compact track machine will enable many contractors to move from wheeled skid-steer loaders to a compact track loader. The new radius lift path loader is 56 inches wide and 124 inches long with bucket and has a 1,400-pound rated operating capacity. The Bobcat® T140 has a turf-friendly lug track that distributes the operating weight of the 6,424-pound loader over a larger area, resulting in 5.0 pounds per square inch ground pressure. The loader offers 16.9 gallons per minute of auxiliary hydraulic flow, is powered by a liquid-cooled 46-horsepower diesel engine and travels 7.2 miles per hour. More than 40 different Bobcat-brand attachments are approved for the new model. Visit Booth G-100.

Write In 279 — Or Reply Online

Bonfiglioli presents the new type 20 in the 700C series (720C3H) of travel drives for crawler machines up to 180 tons. With a torque delivery of 220,000 Nm, it has a standard reduction ratio of 1 to 174 and 1 to 287.2 and allows for a greater torque range. Hydraulic motors from 160 cubic centimeters to 250 cubic centimeters are integrated, allowing additional space to be saved along the unit's length and come equipped with hydraulically released multi-disc failsafe parking brakes. The new 710-M5X180 is a drive for excavator slew drives in the 25-ton to 30-ton duty class and combines a planetary gear unit from the 710T series with a Kawasaki M5X hydraulic motor. The 706CK-MAG50VP is a new travel drive for small size tracked machines designed for mini excavators and is also suitable for small crawler loaders, tractors and machines in the 3-ton to 6-ton class range. Visit Booth S-16339.

Write In 494 — Or Reply Online

The ZB32032 is the newest addition to the Zoom Boom super heavyweight line consisting of the 20,000 pounds capacity ZB20032 and ZB20044 models. With a capacity of 32,000 pounds and a lift height of 32 feet, the ZB32032 features a Cummins QSB 5.9 173-horsepower engine, Dana T32,000 powershift transmission, AxelTech axles, three modes of steering, and frame leveling. There are a number of tool carrier attachments available to meet a wide range of application requirements. Zoom Boom by CareLift has designed rough terrain forklifts since 1974 with seven models in the lineup ranging from 6,000 pounds capacity to 32,000 pounds. Visit Booth G-155.

Write In 512 — Or Reply Online

The North Hall exhibit features machines and services for road site development, underground utilities installation and quarry and aggregates operations including: the D8T tractor equipped with AccuGrade® GOS machine guidance system; 730 Ejector Truck; 930G wheel loader; 345C L excavator; RM-500 reclaimer/soil stabilizer; 325LCR features a compact swing radius; 980H and 988H wheel loaders; customer support services including power train, hydraulic, contamination control, maintenance management, fluids and filters, undercarriage and ground engaging tools, and Caterpillar OEM Solutions presents components for original equipment manufacturers.

The Outside Gold Lot will feature machines and services for general construction and the trades as well as paving. Products on display include 904B compact wheel loader; TH215 compact telehandler; 446D backhoe loader; outdoor demonstrations showcasing skid-steer loaders, multi-terrain loaders, telehandlers, small tractors, mini excavators, CB-114 vibratory compactor; new work tools; updated AP-1055D and AP-800D asphalt pavers; PM-201 cold planer; and RM-300 reclaimer.

Featured in South Hall will be new small to mid-size engines ranging from C1.1 IOPU to the C7 featuring ACERT® technology to meet Tier 3/Stage IIIa emissions standards as well as large engines featuring ACERT technology and a Cat C9 cutaway engine. Perkins Engines Company Ltd. displays 1100D Series fuel-efficient engines designed to power construction equipment.

Visit Booths N-2009 and N-15627; Booth G-130; Booths S-15617 and S-15827.

Write In 266 — Or Reply Online

Cleform's patented Saw Buster can turn a worm gear circular saw into a portable concrete cutting or engraving workhorse. Features include a dual-use handle, standing upright or hand-held position; a cutting depth adjustment up to 2 inches; a handle angle easily changed to operator height; precision front guide flips up to allow close wall cuts; and quick, easy assembly. The saw can be used as an early entry saw for control joints in concrete slabs; group joint patterns in synthetic or stamped stone; decorative concrete sawing or engraving; slab granite, marble countertops and floors, stucco, file, brick, asphalt, and plywood; wall or floor access chaser cuts for retro plumbing or electrical; and roofing removal, ripping long straight cuts. Visit Booth S-8618.

Write In 513 — Or Reply Online

The BB5000 Portable Boring Machine does line boring and blind boring in cramped places where others won't fit and produces torque at low revolutions per minute. The accessories extend its versatility to include facing, grooving, spade drilling, threading, valve repair, and trepanning, with boring diameters from 1.375 inches to 24 inches. The microprocessor-controlled BW3000 introduces a new standard of welding control, uniformity and precision with its patented "step" technology which provides complete weld coverage at the start and finish of the bore. Designate "skip-weld" areas, easily adjust step size and direction, rotation speed and direction, wire feed rate, arc voltage and interrupt, and more, from one central location. The AutoBoreWelder uses the same setup as the BB55000, allowing the user to bore and weld with one setup, and even bore and weld simultaneously with three or more bearings. Visit Booth S-11828.

Write In 514 — Or Reply Online

The patent pending Concrete Washout Systems™ is a portable, self-contained and watertight bin that controls, captures and contains concrete washout material and wastewater. This system and method allows trade personnel to washout concrete trucks, pumps and equipment on-site and facilitates easy off-site recycling of the same concrete materials and wastewater, while protecting the storm drain system from potential illegal discharges. The off-site recycling component of both the concrete material and washwater decreases waste generation, increases diversion and recycling efforts, creating an environmentally sound application. This system replaces other outdated washout BMP's. Visit Booth S-9341.

Write In 515 — Or Reply Online

Providing logistics solutions for the United States and global construction industries, ControlBoard is engineered to solve the problem of resource scheduling, tracking and dispatching crews and equipment in the heavy/highway construction industry. Its design, similar to an electronic whiteboard in that changes can be made quickly and easily, has the power to track changes so that resource conflicts, changes and utilization is always available for review across the company. Visit Booth S-17215.

Write In 516 — Or Reply Online

For your recycle and demolition needs, the CEC 102 × 115 Track Impactor features the 102 × 115 horizontal impactor with remote clearing and heavy blow bars, approximately 700 pounds each. The heavy duty track system, 14 feet 9 inches long and 20 inches wide, transfers less than 13 pounds per square inch and is powered by a Cat C-9 274-horsepower engine, with a hydraulic clutch and repto drive. The CEC 5 × 12 Screen-It is now available on track (Model 512 Track LC). Features include the patented direct feed to the screen, a wheel loader no longer must ramp to feed the unit because of the loading height of 9 feet 6 inches; and the screen self-cleaning ball deck for wet and sticky applications which include top soil, compost, mulch, fuel wood, sand, gravel, and more. Visit Booth SL-650.

Write In 517 — Or Reply Online

Products on display include dump bodies and hoists to include Crysteel's Select Body, The Deuce and Poly Tipper. The ProMax Super Dump features an air-suspension trailing axle from Silent Drive and is available on Crysteel's Select elliptical or square body styles. The trailing axle does not interfere with dumping operations and raises and lowers with standard P.T.O. A patented high-lift hydraulic tailgate extends a full 15 inches allowing up to 6 feet or clearance when dumping. Large debris and bulky items exit quickly and completely. Visit Booth SL-654.

Write In 346 — Or Reply Online

Featured products will include D-A Excelon™ EBS offering engine protection for maximum diesel equipment life; D-A Reliant™ provides protection against deposits and wear for heavy-duty service engines; D-A TorGuard™ meets the lubrication needs of heavy-duty automatic and Powershift transmissions requiring Caterpillar TO-4 or Allison C-4 fluids; D-A PresurFlo™ is used for high pressure hydraulic power systems in construction equipment and stationery industrial installations; D-A GearTec™ works on gear trains and differentials requiring extreme pressure lubricant; D-A ProPlex™, a multipurpose extreme pressure grease for heavy-duty trucks, construction and mining equipment; D-A MagnaPlex™ formulated for heavy-duty service; D-A Crusher is used for extra wear control and longer materials handling equipment life in gyratory, cone and jaw crushers; D-A Heat Transfer Oil No. 300 used in major asphalt heaters and other heat transfer systems requiring mineral oil; D-A HTCF® Oil, an acid-free product for annual or semi-annual cleaning and flushing of heating cores; and D-A HydraSafe™ hydraulic fluid used where government-regulated environmental concerns are important. Visit Booth S-16715.

Write In 518 — Or Reply Online

Master Builders, known for concrete admixture products, services and support for nearly 100 years, has changed its company name to Degussa Admixtures Inc., known for its specialty chemicals. Known as a Total Solutions Provider for all concrete needs, Degussa Admixtures continues to provide innovative products and leading-edge technology. Visit S-8027.

Write In 519 — Or Reply Online

The newest version of Forefront® Construction Management software offers hundreds of new features including a new SQL database structure, the ability to track meeting minutes in its project management module, two new features in its document imaging software and integration with Mircosoft Outlook. Forefront Version 12 is based on the highly scalable SQL database platform, a tool for organizing and retrieving data that benefits construction companies of all sizes as they grow. The meeting minutes enhancement to Forefront Project Management offers easy tracking of meeting attendees, task assignments, proposed change orders, and other items resulting from weekly or monthly job meetings. Visit Booth S-17119.

Write In 520 — Or Reply Online

Wear-resistant Dur-X-Line® concrete batch plant liners solve the cost-effective operation of a variety of batch plant components. Ideal for drums, tilt mixers, aggregate weigh batchers, and tilt mixer blades as well as rotary distributors, dump cones, chutes, bins, and hoppers, Durex urethane liners ensure long-wear life and reduce the buildup of hard concrete inside mixers and hoppers. The liners are lightweight and are manufactured in weld-on sections that are sized to fit any specific wear application or sold as 4 feet by 10 feet sheets. Since 1965, Durex Products Inc. has served the concrete, aggregate, mining, and asphalt industries as a manufacturer of wire cloth, urethane or rubber screening media; screening accessories; and urethane and/or rubber wear parts. Visit Booth C-6573.

Write In 475 — Or Reply Online

Reusable TempRamps offer asphalt crews a chance to save time and money. Mats are laid down, anchored and rolled. When mats are picked up, a clean straight edge remains from which to start paving. The mats can be placed at milled butt joints when the paver is still days away from paving which allows a smooth transition for the motoring public with no car alignment complaints. Once paving crews show up to pave, the anchors are backed out of TempRamps and they are ready to be used again. Visit Booth C-4926.

Write In 521 — Or Reply Online

Enerpac will feature its integrated solutions approach to lift problems and other hydraulic applications. The booth will invite show attendees in with an array of Enerpac's full line of pumps, cylinders, system components, valves, presses, pullers, tools, bolting tools, and other specialty products. Highlighted will be a new line of concrete stressing equipment and its new line of ZU4 Electric Pumps. The new ultra modern pumps not only look different, but they are different from the inside out featuring hydraulic and electrical performance in a minimal size and weight product. It is user-friendly and driven by a powerful 1.7-horsepower universal motor. Enerpac professionals will be available to help visitors find solutions to problems. Visit Booth S-16251.

Write In 330 — Or Reply Online

EquipmentWatch announces their newest online offering — SpecFinder™, a free service that finds and compares specifications for nearly 4,000 models of heavy equipment from hundreds of manufacturers. The powerful search capabilities allow the user to find up to 45 key specifications, such as engine details, transmission, performance data, hydraulics components, weights and dimensions, fluid capacities, and more. Performing side-by-side comparisons of up to five models to determine which equipment will meet the user's needs can also be made. Visit Booth C-6124.

Write In 522 — Or Reply Online

Everpads™ for road milling equipment are made of tear/wear resisting rubber of high elasticity. They provide traction and a smooth ride, protects undercarriages and the environment; there is no chunking off and no loosening; and they come with a 1,000-hour warranty. They are easy to install and replace by bolting down to grouser from behind. A variety of rubber pads are available to suit your needs. Visit Booth C-4827.

Write In 523 — Or Reply Online

As a manufacturer of pneumatic blowing equipment, Express Blower™ offers its models in three different power levels of standard, medium and heavy duty. The standard power unit applies mulches, wood chips, and some lighter soil and compost blends. The medium duty or MD model is designed to apply these products, as well as heavier materials such as soil blends, compost, sand, and aggregate. The heavy duty or HD model is built to blow rock all day as well as spreading the other products. The MD and HD models are efficient in applying erosion control blankets and berms for the erosion control market with a capacity to reach areas up to 800 feet from the unit. Visit Booth S-10651.

Write In 524 — Or Reply Online

In addition to launching two new products, Extec will be displaying the S-5, S-4 and S-3 series of screening plant as well as the C10 and C12 tracked jaw crushers and primary and secondary impact crushers. Visit Booths C-6051 and S-545.

Write In 525 — Or Reply Online

FCC Attachments has released a new product to add to their existing Telehandler attachment line, the Scrap and Trash Grapple Buckets for Rough Terrain Fork Lifts. Available in two capacities, 1.0 cubic yard and 1.75 cubic yards, the dual grapples are individually operated to grab uneven loads and the cut out end plates make it easier to handle various lengths. Various applications include scrap, trash, pipe, logs, brush, and round bales. The Trash Grapple buckets are also available in two capacities, 1.75 cubic yards and 2.25 cubic yards. The full-end plates and the one-piece grapple secures loose material. Various applications include scrap, trash and brush. All models are 96 inches wide with a lift capacity of 10,000 pounds and an operating weight of 36,000 pounds. An optional bolt-on edge is also available. Visit Booth N-1461.

Write In 307 — Or Reply Online

Finlay Hydrascreen displays a full-line of scalping, screening and stockpiling plants; reclaimer; trammels; and washing plants. The three-way and four-way split screening plants combine scalping, screening and stockpiling into one integrated unit. Models include the 663, 683 and 693 and 694, available on wheels or tracks, with screenboxes ranging from 4 feet by 10 feet up to 5 feet by 20 feet three-deck types and are designed to work independently or with tracked crushing plants. The 883 Reclaimer is a high performance, heavy-duty, screening plant for cost-effective processing of aggregates, topsoil, coal, crushed stone, and C&D debris at up to 500 tons per hour and the new 740 Trommel has a 5-foot by 13-foot reversible barrel, four-wheel drive and 180-degree fines swivel conveyor. Finlay's mobile washing plants can be configured as Hydrasander dewatering/classifying systems or Sandmaster mineral-classifying cyclone and dewatering units, designed for quick installation and ease of relocation. Visit Booth N-1009.

Write In 368 — Or Reply Online

Fisher-Klosterman Inc. provides air pollution control equipment, high-efficiency cyclones, bag houses, cartridge collectors, air classifiers, and related services, systems and accessories. The company's Buell Division has supplied Air Classifiers to the aggregate industry for 20 years. Buell Systems provide a dry process using only ambient air to create manufactured sand for asphalt, concrete sand and mineral filler. These systems are available in both stationary and mobile units. Features include no moving parts within material flow stream; eliminates settling ponds, little or no maintenance, low power consumption, minimum or no adjustment during operations; and a laboratory test facility is available to verify results. Visit Booth C-6179.

Write In 526 — Or Reply Online

General Equipment Company now offers the SG12/E single-head surface grinder, designed to smaller-scale surface preparation projects. The grinder offers high performance, durability and ease-of-use, making it ideal for professional contractors and do-it-yourself homeowners. Powered by a totally enclosed, fan-cooled 1.5-horsepower electric motor, the SG12 features a single rotating disc with a 12-inch-wide working width. Visit Booth C-4358.

Write In 257 — Or Reply Online

Gomaco's line of slipform concrete highway pavers has an added detachable telescoping auger/strike-off giving contractors a mold that can be either an open front or auger/strike-off. It can then easily be broken down with removable and telescoping sections. Designed to move independently with hydraulically adjustable mounts on the front of the mold, a self-supporting transition adjuster (TA) is standard to allow for crowning in the material. Both strike-off and auger have 6 feet of telescoping capabilities to aid in changing paving widths. To change widths, add or remove a section of the paving mold, and telescope the auger and strike-off in or out depending on the width. The telescoping auger incorporates bolt-on flighting to accommodate the changing widths. The auger/strike-off mold will be displayed on a new generation GHP-2800 paver. Visit Booth S-8205.

Write In 277 — Or Reply Online

Through a series of video presentations, Grasan highlights their capabilities in road-portable, pit-portable and stationary crushing, screening, conveying and storage/handling equipment and systems for concrete/asphalt recycling and aggregate systems of all kinds. Grasan can design and build or upgrade entire systems, component systems or specific equipment. The company's newest development is a line of large, track-mounted primary crushing plants that are each largely custom designed and built to meet individual customer needs and specifications for high-production aggregate applications. The plant can be built around any impactor or jaw crusher, whichever best fits the client's operation. Visit Booth C-6239.

Write In 276 — Or Reply Online

The PS1200 Placer/Spreader, a high-production placer/spreader that can be transported in a single loader under 12 feet wide, and the Eagle 6500SS Side Shift Trencher designed for digging highway edge drains, have been added to G&Z's line of concrete construction equipment. Also on display will be the mid-size S850 Quadra Concrete Slipform Paver and Compact Dowel Bar Inserter, a midsize paver capable of paving widths from 12 feet to 34 feet, used in urban and residential paving work as well as highway and airport concrete pavements. Features include reduced time to load, unload, set up, tear down, and change widths; the narrow profile design allows paver to work as close as possible to obstacles and in tight confines; use of high quality, state-of-the-art electronic and hydraulic circuitry; reduced heat and noise exposure for operator; exceptional operator visibility, paver maneuverability, ease of operation and troubleshooting; and structural integrity. Visit Booth S-812.

Write In 527 — Or Reply Online

HEF Group has developed a spherical bushing based on PEL BH technology, meeting the requirements of manufacturers who want to reduce joint maintenance costs. The technology, with its duplex surface treatment for increased wear resistance and its large grease reservoirs, enables reduced joint maintenance. Lubrication intervals may be increased up to 1,000 hours. In addition, these new spherical bushings have increased ductility for excellent shock resistance. Visit Booth S-16744.

Write In 528 — Or Reply Online

Movax Robotic Pile Hammer SP 50 on a Cat excavator handling steel sheet piling in a jobsite environment, Movax SP 100 Robotic Pile Hammer; Movax EM 60 and EM100 excavator mounted vibratory hammer and HMC excavator mounted drill are just some of the products to be highlighted. On display for the first time will be the Morax Excavator Mounted Hydraulic Impact Hammer, an impact hammer designed to drive pile using an excavator. Other products include Poseidon Sectional Barges, three different styles of truck-able barges are available for sale and rent; Movax Excavator Bucket positioning system installs on your excavator allowing operator to grade a trench, slope a wall, determine bucket depth, as well as bucket position, right from the in-cab computer screen; and the Movax Robotic Sheet Pile Hammers can unload the piling from truck, pick up a pile horizontally, move it to the vertical position and drive to grade using an excavator. Visit Booth S-864.

Write In 529 — Or Reply Online

Suspension products and technology for the commercial trucking industry will include HAULMAAX®, a rear rubber vocational truck suspension; PRIMAAX®, a rear heavy-duty, air-ride suspension truck system; AR2™, a walking-beam, air-ride truck suspension; INTRAAX®, extreme-duty 30,000-pound capacity axle and trailer suspension system; and COMPOSILITE FBC™, 8,000-pound capacity, self steering auxiliary axle; and COMPOSILITE FX™, fixed-axle lifting suspension system for trucks and trailers. Hendrickson International has supplied truck and tractor suspension, trailer suspensions, truck and trailer lift axles, springs and bumpers to the commercial transportation industry for 90 years. Visit Booth S-8127.

Write In 428 — Or Reply Online

To improve resistance against abrasion and impact and extend parts life for implements in the construction/aggregates industry, Hobart showcases its McKay brand of welding products featuring ArmorWear™ hardfacing self-shielded tubular wire as well as VertiWear® 600 and VertiWear AP, hardfacing gas-shielded tubular wire. As an overlay for carbon and low alloy steels, ArmorWear self-shielded flux-cored wire offers resistance to adhesive (metal-to-metal) wear, abrasion and impact while depositing a premium martensitic alloy steel of H-12 tool steel composition and maintaining its hardness up to 1,000 degrees Fahrenheit. As deposited on 1020 steel, the wire has a hardness ranging from 47 Rc to 53 Rc, for one to three layers and optimizes performance on 110/120-volt type wire welding machines. ArmorWear has a steady arc and smooth spray transfer. VertiWear 600 provides crack free, multiple layer deposits at a hardness of 55–60 Rc, with DCEP (reverse polarity); and VertiWear AP provides exceptional impact resistance while work-hardening to 50–55 Rc. Visit Booth G-244.

Write In 476 — Or Reply Online

Hydro Engineering Inc. will be demonstrating the Hydrosite® Portable Wash Rack System in conjunction with its patented Hydropad® portable wash pads. These equipment packages allow its owner the flexibility of moving a wash site to any location quickly providing a durable and environmentally friendly wash pad. The system includes all necessary equipment required to collect the wash water and recycle the wash water for re-use through its integrated Hydroblaster pressure washing systems. This full integrated portable system provides a continuous operation of washing, collecting and recycling; is factory installed and tested in its own portable enclosure. Requirements include a relatively flat hard surface to place it on and utilities required are 200 amps of 208-volt, three-phase power and a garden hose water supply. Visit Booth S-859.

Write In 530 — Or Reply Online

The 12 mini excavators from IHI are small excavators with digging depths of 5 feet 2 inches to 14 feet 1 inch and powerful bucket forces of 2,160 pounds to 14,730 pounds. Smaller units are available to homeowners with yard products and small utility contractors as well as larger units to meet general contractors' deeper digging depths and power requests. With features of a larger mini excavator, the line offers three styles of excavators and component dependability. Visit Booth C-5723.

Write In 418 — Or Reply Online

Two new hydraulic, compact excavators, the 7.5-metric-ton ZX075 and 12.5-metric-ton ZX-125 provide powerful performance for work in building, landscaping, rental applications, and utility installation, as well as general construction and repair work. The ZX-75 has an operating weight of 16,538 pounds; 72-horsepower, four-cylinder turbocharged diesel engine; and maximum digging depth of 13 feet 11 inches. The ZX-125 has an operating weight of 27,563 pounds; 94-horsepower, four-cylinder turbocharged diesel engine; and a maximum digging depth of 15 feet 4 inches. Both machines feature zero tail swing, allowing excavators to safely operate close to buildings and in tight jobsite conditions. Articulated boom systems provide increased capability outside and parallel to the tracks for excavation within the entire width of the machine without repositioning. Auxiliary hydraulics are standard on both excavators, expanding versatility and productivity by allowing a greater range of attachments. Visit Booth G-200.

Write In 319 — Or Reply Online

The Model RS Mid Belt Sampler is designed to take representative samples from moving belts and materials up to 4 inches may be sampled. The sampler provides for a safer and more representative sample and eliminates the need to have an individual assigned to the sampling process. The Model RS sampler meets ASTM specifications for automatic sampling. Visit Booth S-11246.

Write In 531 — Or Reply Online

The Italian Trade Commission, in conjunction with COMAMOETER and UCoMESA, are representing numerous Italian manufacturers, and will display the latest Italian off-road construction machinery, components and attachments. Machines manufactured for construction, earthmoving, road building, waste handling, and demolition industries as well as information on equipment companies actively exploring distributor and OEM business partnerships in North America will be available. Visit Booths N-2572 and N-2569.

Write In 532 — Or Reply Online

The full line of Tier 3/Stage III A off-highway engines along with their drivetrain components offers emissions compliance as well as cost-efficient flexibility with PowerTech Plus® engines for performance markets and PowerTech™ engines for markets that require fewer features. The 4.5L Tier 3/Stage III A Power Tech Plus models provide a power range from 155 horsepower to 185 horsepower; the 6.8L from 140 horsepower to 275 horsepower; the 9.0L from 225 horsepower to 400 horsepower; and the 13.5L from 350 horsepower to 600 horsepower. For other markets, Tier 3/Stage III A PowerTech engines are available in a 4.5L with a power range of 80 horsepower to 140 horsepower, or a 6.8L ranging from 140 horsepower to 200 horsepower. Funk Manufacturing, a subsidiary of John Deere Power Systems, will display some of its powershift transmissions, axles, pump drives, and planetary gear drives for off-highway, industrial, construction, marine, mining, petroleum, and agricultural equipment manufacturers. Visit Booth S-15639.

Write In 533 — Or Reply Online

Designed for work on roadways, bridges, in urban areas, or any site where space is limited, KAC introduces the PC308USLC-3 hydraulic excavator with an occupied width of 17 feet 5 inches or less with a loaded bucket. The 179-horsepower machine offers a maximum ISO-rated digging force of 44,530 pounds and an arm crowd force of 33,290 pounds depending on arm length. The excavator weighs 73,146 pounds and offers drawbar pull (59,180 pounds maximum) and steering force. When equipped with 33.5-inch shoes, the machine occupies a width of 10 feet 9 inches and the counterweight protrudes 1 foot 5 inches past the track shoes. Powered by Komatsu's six-cylinder SAA6D102E-2 engine, the excavator hydraulic system, with a maximum flow of 119 gallons per minute, is powered by HydrauMind™. Three working modes (Economy, Lifting and Breaker) are designed to match engine speed, pump speed and system pressure to each application. Visit Booth N-2515.

Write In 534 — Or Reply Online

The Caterpillar 320 model excavator versions of the SHARC™ (Shanks on an ARC) Multi Ripper™ and the Multi-Ripper Bucket will be on display as well as the WagMann Wedgelock pin-grabber Quick Coupler. The Multi Ripper's and Multi-Ripper Buckets' patented-pending technology utilizes short staggered shanks that hit one at a time to provide maximum breakout force sequentially to each tooth. The constant tip radius leaves a relatively flat bottom in the trench and has the ability to rip the sides of the trench easily. Constructed out of AR400 steel and using standard replacement teeth, they are available for any excavator or TL backhoe above 6,000 pounds. Visit Booth G-396.

Write In 325 — Or Reply Online

The new 25,300 pound 785 Motor Grader features a 13-horsepower Cummins turbo diesel engine; 12-foot sliding moldboard; all-season enclosed cab option; six-speed Powershift transmission; front-mounted 46-inch scarifier and articulated frame. The beefed-up LeeBoy 8515 includes an 8-foot to 15-foot paving width with dual operator stations. Other features include a 74-horsepower Hatz Silent Pack Engine; 12-inch-diameter sonic augers; heavy-duty vibrating, heated Legend Screed System; high deck/low deck configuration; 7.5-ton hopper; heavy-duty radius hopper wings; and continuous rubber track or poly pad track. Expanding its line of asphalt pavers with the 8816 Asphalt Paver, LeeBoy offers this 25,000-pound, 130-horsepower, track-mounted paver designed for road and large commercial applications. It includes an 8-foot to 15.5-foot paving width, vibrating, heated Legend Screed System; independent sonic auger and conveyor controls; patented under auger cut-off plates; dual operator stations; 10-percent screed extension slope; and 10-ton receiving hopper. Visit Booth C-4727.

Write In 260 — Or Reply Online

Spanish tower crane manufacturer Linden Comansa will exhibit two cranes, the LC-5211 with 172.2-foot jib and the new model of the 2100 Series, the 21LC550 with 262.4-foot jib. Maximum load is 11,025 in four part-line for the LC-5211 and a maximum of 18,000 pounds in four part-line for the 21LC550 which has a larger, roomier cabin, but with the same frequency-controlled drive system for hoist and trolley. The tower system can be dismantled into panels for transporting long distances. The interchangeable, bolt-on feet system allows the base to be used with all Linden Comansa masts, allowing freestanding heights of up to 212.9 feet on the 2100 series. Sister company, Linden Comansa America LLC is a joint venture of Linden Comansa and Heede Southeast. Both companies have over 80 years of tower crane experience. Visit Booth G-184.

Write In 545 — Or Reply Online

Lovejoy® ROSTA® features technological advancements and choices for the aggregate and mining industries with its line of tensioners, damping and vibration-limiting parts and equipment. ROSTA products are based on rubber-suspension elements replacing metal springs and spring and bearing combinations, reducing component and assembly costs and providing product reliability and performance. With no metal-to-metal contact, elements eliminate the need for lubrication, avoid failures caused by moisture and rust, diminish audible noise associated with moving metal parts and are maintenance free. Several demonstrations are planned. Visit Booth S-14016.

Write In 546 — Or Reply Online

The Mastermag SCB Heavy Duty Magnet is introduced as an upgraded, long-life permanent crossbelt overhead separator and features Tri-Polar? Magnetic Circuitry. Using this circuitry, problems such as magnetizing of steel frames, rollers, and other steel equipment within close proximity to the magnet are solved. This peripheral magnetic leakage whereby the magnetic field "leaks" beyond its intended area is taken care of as the entire magnetic field is directed straight down onto the conveyor; over the material being processed and especially the tramp iron to be removed, making the magnet 30-percent more powerful. Designed for easy belt removal and refitting with an endless belt, an optional armor-clad belt is offered for extreme applications in heat or handling abrasive and/or sharp materials. Constructed from individually replaceable stainless steel plates, the armor covering increases the operational life of the belt and reduces damage to the magnet system. The drive system is available with electric and hydraulic drives. Visit Booth C-6714.

Write In 547 — Or Reply Online

Flex-Mat® 3 High-Performance, Self-Cleaning Screen Cloth is offered in screen opening sizes from 40 mesh to 4 inches in numerous wire diameters, so mining, aggregate and demolition/recycle producers can fine tune their self-cleaning screening solutions for maximum output. Flex-Mat 3 is a combination of polyurethane strips bonded with individual wires that eliminates the need for woven tires, lasting three to four times longer. Centered on each screen deck crown bar for support, the polyurethane strips allow the individual wires to vibrate independently and at different frequencies to prevent material from accumulating between the wires. Since 1884, Major Wire has designed, manufactured and marketed Flex-Mat® 3 High-Performance, Self-Cleaning Screen Cloth, Optimum Wire® woven tempered and stainless steel wire cloth and polyurethane panels for the quarry, mining, recycling, and industrial markets. Visit Booth C-6873.

Write In 548 — Or Reply Online

Developed for contractors of all types and sizes, ICE 2000 Basic System features takeoff and conceptual estimating tools; user-defined work breakdown codes that can represent alternates, components, systems, or any of 35 different user-defined categories; labor pricing based on crews, man-hours, unit prices or any combination; an easy-to-use report designer; and interfaces to trade pricing services. Other enhancements include the new featured, Capture Desktop, which allows estimators to perform accurate and precise virtual takeoff from digital plans; spec-driven takeoff for industrial piping; new interfaces to accounting and scheduling software; and a new bid day function. ICE 2000 reduces takeoff time, allows more work to be bid and offers more time to study jobs. Visit Booth S-17410.

Write In 549 — Or Reply Online

Marcotte Systems Ltd. provides customized batching and plant control software. Under a Windows-based platform using XML, the Batching Control System, Dispatching System and Construction ERP System provide reliable, user-friendly and flexible technology. Systems can be customized to the specific needs and application of each customer whatever their field or industry: Ready Mix, Precast, Block, or Paver. Visit Booth S-10052.

Write In 550 — Or Reply Online

The Silt Fence Plow™ now features a rear-pivot design that enables tighter turns to easily allow J-hooks when installing silt fence. The positive feed design allows fence to be installed up to 20 inches deep and reduces bunching and tearing of material. The machine can be used in most soils, can be attached to a skid steer or the three-point hitch of a tractor and an optional offset attachment is available. Visit Booth C-7109.

Write In 551 — Or Reply Online

The VSK100G Pick-Up VaXcavator features a dual position air filtration system which expands the usage of the VSK100G to many dry applications. The cyclone separator can be positioned after the collection tank for wet and most dry applications, and for applications involving light debris. The cyclone separator can be easily moved to the top of the collection tank for maximum separation. Other features include a full opening tank door with quick-lock closure, electronic low water shut off and vacuum shutdown, 575 cubic feet per minute positive displacement vacuum blower, 100-gallon collection tank, 50-gallon fresh water tank with high-pressure water system delivering 2.6 gallons per minute at 3,000 pounds per square inch, and powered by a 24 horsepower, air-cooled Honda engine. A two-nozzle Reduction Tool for faster digging is standard. Made to access areas that larger vacuum excavators and vacuum trucks can not reach, the VaXcavator fits in the back of any pickup truck. Visit Booth C-4519.

Write In 285 — Or Reply Online

Metal Forms Corporation's product line includes steel and poly forms as well as one-man finishers and truss screeds. The "Hands On" poly section allows attendees to handle 12-foot lengths of Poly Meta Forms® plastic forms and insert hardware as if they were on a job site. Flexible forms can be bent to form a 3-foot radius and both flexible and straight forms can be stacked up to 18 inches high. The company's line of steel forms are manufactured for all types of concrete construction including flatwork, curb and gutter, paving, and barrier walls. The line of truss screeds includes the Mighty Lite™, Heavy Duty™ and Cruiser™ as well as double handle one-man finishers for all types of concrete paving and finishing applications. Visit Booth S-8940.

Write In 355 — Or Reply Online

Crushing and screening technology, customer service, equipment automation, and complete systems engineering will be on display. Products include: the new Lokotrack LT200HP and LT111OS mobile crushing plants, part of the "Jubilee Series"; new Lokotrack ST352 mobile screen with SmartScreen® technology; Nordberg CV100 mobile screen; optimized Nordberg C145 jaw crushers; Nordberg HP800 cone crusher; new FS303 flat screen; customer service area including product raining presentations twice daily at 10:30 a.m. and 2:30 p.m.; new Barmac B6150 VSI crusher; Barmac V1200 VSI crusher; new NW3054 portable jaw plant; complete systems and application engineering; and automation technology. Metso marks 20 years in track-mounted crushing technology. Visit Booth C-5729.

Write In 410 — Or Reply Online

Michelin unveils the X Super Terrain AD radial tire, the newest E4 radial tire primarily used on articulated dump trucks. The tread design supplies excellent traction and ride comfort and the extra deep tread depth and special rubber compounds provide durability and long tire life while its rugged shoulder design enhances sidewall protection and resistance to damage. Made for rigid dump trucks and bottom dump trucks, they are ideal for haul trucks operating at thigh speeds, and are currently available in 18.00R33 size. A new size, 24.00R35 will be introduced in third quarter 2005. Visit Booth N-2563.

Write In 472 — Or Reply Online

Mikrofyn A/S, a Danish manufacturer with over 18 years of designing and manufacturing lasers and machine control systems, introduces into the North American market 25 models of lasers, three models of stand-along visual laser machine detectors, three models of real-time excavator systems, a full-range of 2-D and 3-D GPS/LPS automatic machine controls for dirt moving machines, asphalt pavers and milling machines. Visit Booth S-18005.

Write In 552 — Or Reply Online

Of special interest to the construction and aggregate industry are the XMT® 350 CC/CV and XMT® 350 VS multi-process inverters featuring Auto-Line™ technology designed for those who perform Stick, TIG, pulsed TIG, MIG, pulsed MIG, flux cored, or air carbon arc cutting and gouging. Both Bobcat™ 250 and Bobcat™ 225 engine-driven welding generators have Accu-rated 10,000 watts of useable peak generator power. The Bobcat 250 features a fully enclosed case, super-tough XENOY® protective armor on the front panel and a 12-gallon fuel tank. Under a continuous load of 4,000 watts of generator power, the Bobcat 250 can run for about 14 hours. Bobcat 225's rotor design optimizes generator performance for smoother power. Trailblazer® 302 and Trailblazer® 275 DC engine-driven welding generators feature four preset Dig settings, provides a fully enclosed case, XENOY protective armor; and the Trailblazers' digital meters feature SunVision™ technology. Visit Booth G-244.

Write In 265 — Or Reply Online

Morbark's "Island Paradise" booth will display wood processing equipment including the Model 1300 tub grinder, the 6600 Wood Hog and 4600 Track Wood Hog horizontal grinders, the Morbark Predator, a high-torque, slow-speed shredder, the 2400XL brush chipper with loader, the 20/36 Track Chipper and Model 60 Talon Debris Shear. An operator's platform is now standard equipment on the Model 2400XL Hurricane with loader, a unit equipped with operator's seat with joystick controls and feed controls that can be switched from loader-fed to hand-fed. Morbark Model 6600 Wood Hog on tracks, a durable grinder with self-propelled mobility offering wood waste processors is designed to move and grind simultaneously. With remote control of all machine functions, the 6600 on tracks can be operated from cab of an excavator or loader. Engine options range from 860 horsepower to 1,000 horsepower and the Caterpillar 330L undercarriage provides 18 inches of ground clearance and wide stance for steep grades. Visit Booth S-528.

Write In 553 — Or Reply Online

Multiquip supplies concrete and masonry saws, tile saws and a variety of wet- and dry-cutting diamond blades. Upgraded HSC combination blades, available in 12-inch to 2-inch diameters, cut concrete, asphalt, brick, block, pavers, soft stone, and roof tile, and can be used on high speed cut-off saws, low horsepower walk-behind saws and stationary masonry saws. Side Winder wafer-style tuck point series are offered in two and three blade designs with 1/4-inch and 3/8-inch thicknesses, respectively, and remove grout and mortar from between bricks and concrete blocks. GloBug light towers, offered as a stand-alone unit, or with a cart for an optional generator, features maximum mast heights of 13 feet and 16.5 feet, come standard with a water-resistant balloon; illuminates to distances in excess of 150 feet, and a 1,000-watt metal halide lamp provides glare-free illumination. The DuoScreed, well suited to jobs such as sidewalks, driveways and decks, is powered by a four-stroke, 1.5-horsepower Honda GX-31 gasoline engine and weighs 32 pounds. Visit Booth S-555.

Write In 254 — Or Reply Online

Mustang Manufacturing introduces two new compact excavator models — the 5003ZT and 6003. The 5003ZT has a zero tail swing design whereas the 6003 is a short-tail machine with a larger engine, increased hydraulic power, a longer boom and one of the largest operator cabs in its class. Key features of the 6003 include 12,566 pounds operating weight; 68 horsepower at 2,100 revolutions per minute Tier II Yanmar engine; 12-foot-6-inch maximum digging depth; 39.6 kN maximum bucket digging force; 21.9-gallon fuel tank capacity; 1.07/2.9 miles per hour travel speed (dual); and 98.4-inch track length. Visit Booth N-2863.

Write In 405 — Or Reply Online

National Attachments Inc. and NYE Manufacturing have created the Hercules Grapple. With complex internal bridging and gussets, slot welding, multi-alloy steels, including CHT 400/500 replaceable jaw inserts, routine maintenance is virtually eliminated. Ideal for extreme service applications, the grapple comes complete with mounting bracket and three-position deadman. Other features include high-volume 3/4 tine configuration, bulk-capacity 4/5 configuration, as well as 2/3 demolition-configuration. Visit Booth N-2806.

Write In 554 — Or Reply Online

The National Drilling Association (NDA) will feature two days (March 17–18) of meetings and presentations focused on the geotechnical, environmental and mineral exploration sectors of the drilling industry. The first day will include committee meetings and board meeting. The second day features a series of industry-specific presentations addressing both management and technical drilling issues. Topics include DOT compliance, direct-push methods, sampling procedures, diamond drill bit selection, a mud course, and developing an effective safety training program. Reception and dinner take place on the final night. NDA, founded in 1972, promotes the use of professional drilling contractors and their methods and has more than 250 international member companies. Visit Booth L-3605.

Write In 555 — Or Reply Online

The PRO 3200 line of concrete power screeds features patented Northrock magnesium blades that cut and roll the concrete in front of the screed, available with blades from 4 feet to 14 feet for one-man operation and 16 feet to 22 feet for two- man operation. A choice of a 31cc, four-cycle Honda or 34cc, two-cycle Robin gasoline engine is offered. Other power screeds include the gas C*A*T* series, air C*A*T*series, panel screed series for slope work and one-man screed for sidewalks and rail pours. Concrete poker vibrator systems, designed to consolidate concrete quickly and easily, come with a range of vibrator heads, flexible shafts and power sources and Northrock's backpack vibrators are designed for the consolidation of concrete in remote areas where electrical power is not available or on sites where extra mobility is desired. Flexible shafts and vibrator heads are driven by a powerful, yet fuel-efficient and quiet two-cycle, 50cc, 2.5 horsepower engine. Visit Booth S-9231.

Write In 314 — Or Reply Online

Otto developed a series of Hall Effect digital and analog output control devices resistant to EMI and RFI interference. A certified, independent lab verified that the OTTO HP, HPL, HPLR, and JH Series of products are immune to 100 V/meter RFI and EMI per SAE J1113-22. Products include pushbuttons with digital on/off and analog linear outputs, rocker switches and thumbwheels with dual analog or digital outputs and a dual axis joystick and single axis foot pedal with up to four analog or digital outputs which can be used in conjunction with analog outputs to verify control position and dual outputs can be used to provide redundancy; electrical life up to 15 million cycles. PWM, CAN (J1939 and Open) as well as custom output options are also available. Electronic enclosures are sealed to withstand a one meter, 30-minute immersion. OTTO Hall Effect products can be mated to the OTTO Universal Grip control handle or incorporated in custom handles and enclosures. Visit Booth S-18004.

Write In 556 — Or Reply Online

Model 6700, a horizontal recycler, is a high-powered addition to Peterson's line, powered by a 1,000-horsepower Caterpillar 3412E diesel engine. The 6700 will meet the demands of land clearing contractors, and processors of construction and demolition debris and municipal solid waste. Features include Peterson's "Advanced Control System" control logic and the Peterson Impact Release System introduces a new standard in its ability to handle contaminated feed stock. By using a three-stage grinding process with an up turning rotor and large grate area, material can be produced to exact specifications. A quick-change multiple grate system makes it easy to customize grate configurations to produce a wide variety of finished materials. Since 1982 Peterson has specialized in developing delivery and processing equipment that turns low-grade organic materials into high-value products. Visit Booth S-504.

Write In 557 — Or Reply Online

The Petrogen Oxy-Gasoline Cutting Torch System uses regular liquid gasoline as fuel, replacing acetylene for cutting steel. Safe, fast, powerful and economical to use, fuel is liquid from tank to tip, making fuel line backflash impossible. The Petrogen flame jumps air gaps, cuts through layers and punches deep holes fast; and cuts through rust, paint and oil without hesitation. Petrogen's ASME-code fuel tank holds 2.5 gallons of gasoline, equivalent to 250 cubic feet of acetylene with no increase in oxygen consumption. The gasoline flame oxidizes steel 100 percent so sparks are lighter weight and less hazardous. A Portable Cutting System (PCS) backpack cutting unit is also offered. Recommended by the U.S. Department of Energy, the system is listed by UL, used by U.S. Homeland Security and FEMA; tested and approved by U.S. Navy and Coast Guard; allowed by MSHA in all mines; and made in the United States. Visit Booth S-573.

Write In 558 — Or Reply Online

The Power Curber 5700-SUPER-B features a 133-horsepower engine increasing the machine's trimming and pouring capabilities in high-production curb-and-gutter applications. The operator's platform and console have been raised to increase visibility of the auger and chute man. The redesign results in less motion for operator and the work area is cooler with hydraulic and engine coolant radiators re-located and mounted externally so that hot air circulates away from the operator's platform. The new hydrostatic direct-drive conveyor has higher torque; crawlers have a heavier frame and increased torque for easier loading or pouring on inclines and working in soft-grade conditions. Other features include rotary controls allowing fractional changes in ground or conveyor speeds; and the machine is easier and faster to service with filters for fuel, engine oil, air and the high-pressure servo located at eye level and in easy-to-reach positions. Visit Booth S-8637.

Write In 442 — Or Reply Online

Power Pavers Inc. manufactures the PS-2700 for placing and spreading concrete for highways and residential streets. The placer spreader places concrete in front of paving machines at widths from 12 feet to 27 feet wide, with optional extensions up to 32 feet wide. While the machine accomplishes dual-lane spreading in a single pass, the PS-2700 paves depths to 14 inches thick and has self-loading legs which can lift 42 inches, allowing backing a lowboy beneath the machine for easy loading. The machine cleans, loads and is ready to go in 60 minutes. Disassembly is not needed for moving, eliminating a crane for setup and the conveyor belt is mounted beneath the machine. The PS-2700 can cycle an 8-yard dump truck in 30 seconds. Power Pavers, established by Power Curbers Inc. manufactures slipform pavers, form pavers and a texture cure machine, as well as placer spreaders. Visit Booth S-8637.

Write In 442 — Or Reply Online

Since 1947, Process Heating Company (PHCO) has been producing low maintenance simple-operated and reliable heating systems based on cost-effective electric heat. They can apply to retrofit or new equipment and are completely safe since there is no flame or emissions. PHCO immersion heaters are safe, efficient, environmentally sound electric heat for asphalt tanks. PHCO preheaters are inline heaters that heat the fuel before the burner providing maximum efficiency and substantial savings. Visit Booth SL-866E.

Write In 559 — Or Reply Online

Rayco Manufacturing Inc. designs and produces a complete line of environmental equipment and introduces a new product line of Brush Chippers, beginning with its 6-inch disk brush chipper, the RC 6D. A 25-horsepower Kohler V-twin engine produces torque ratings of 39.5 foot-pounds at 2,800 revolutions per minute generating high performance, while providing long-life and easy maintenance for the RC 6D. Ideal for rental applications due to enhanced safety features and economical performance, the machine's reversing auto feed keeps the RC 6D at the correct revolutions per minute level to create more uniform chips, uses less fuel and minimizes vibration. Strong, but lightweight, the brush chipper is easily towed behind a pickup truck and its highway lighting features conform to Federal Motor Vehicle Standards. Visit Booth N-2804.

Write In 560 — Or Reply Online

Reynolds International LP offers 40 models of pulled-type scrapers of varying capacities from 5 yards up to 20 yards. Its new 20E12.5 Scraper is an "ejector" scraper ideal for mining operations, road, levy, pond, airport, and general construction and mining applications for use with tractors in the 375-horsepower to 500-horsepower range. The 20E12.5 utilizes Reynolds patented "SDS" (synchronized displacement system). Features include a retractable floor; multi-function hydraulic valve block; ejector/floor roller bearings; cylinder safety stops; height adjustable axle mounts; heavy-duty roller bearing hubs; tandem hitch and hydraulics; and 23.5R25VUT radial tires. Visit Booth N-2259.

Write In 561 — Or Reply Online

Repair cracks and spalls from the inside out with Concrete Mender. With a surface tension one-third that of water, Concrete Mender penetrates deep into cracks and spalls, bonding to aggregate within the concrete. Complete load transfer is achieved in just 10 minutes. It works in freezing cold to desert heat and is compatible with most concrete overlays and coatings. Visit Booth S-10902.

Write In 562 — Or Reply Online

RoMix Inc. has developed a safe alternative to harsh acids that removes hardened cement without damage or hazardous working conditions. Back-Set will dissolve concrete at the molecular level causing it to break down and lose its bond. It is non-corrosive (ASTM G-31), NonDOT Regulated (CFR49 Sec. 173.24), Readily Biodegradable (ASTM E1720-01), and safe on paint (PPG and Dupont) and the user (safe to skin and metal per DOT/OSHA test protocol). The unique chemistry replaces such acids as hydrochloric, muriatic, phosphoric, hydrofluoric, sulfuric, and is not a low pH salt. BackSet is formulated to be used undiluted to remove cement, concrete, mortar, grout, and stucco from virtually any surface. The recommended method for application is spraying, but can be foamed on to saturate the hardened concrete. After waiting 15 minutes, and performing a second saturation of the same area, concrete should start to lose its bond after 20 to 30 minutes followed by rinsing with water. Visit Booth S-11129.

Write In 563 — Or Reply Online

Track-driven vibratory soil compactor, CV550, has the traction and gradability to climb steep slopes up to 100 percent or 45 degrees while compacting. Roller SV201TB, capable of developing 400 pounds per inch of total applied force over its 54-inch wide padfoot drum, speeds compaction of fine materials. SV505 Series Vibratory Soil Compactors are available in a smooth drum configuration. SV505D, used for rock fill, granular soils and semi-cohesive materials; SV505T used for cohesive silts and clay. Models feature drum drive combined with drive at rear wheels for added traction over rough terrain. For tender mix Superpave applications, stiff HMA mixes and SMA is the GW750 Vibratory Rubber Tired Roller with gyratory action. SW900, vibratory roller with 4,000 vibrations per minute capacity and 84-inch drums, is one of three vibratory rollers series which includes SW800 and SW850. Mid-sized, double drum vibratory asphalt rollers for public works and smaller compaction jobs are the SW300, SW320 and SW330. Visit Booth S-620.

Write In 278 — Or Reply Online

Highlighting technology in drilling, crushing and tooling available for rock excavation operations in construction, mining, quarrying, and civil engineering, four product groups to be displayed include Tamrock, Driltech, Sandvik Rock Processing, and Sandvik Mining and Construction tools. Commando 120 is ideal for small-diameter hole drilling force in foundation, road cutting, trenching, bolting, or demolition tasks. Titon 500, a new member of the diesel-powered, self-contained crawler-mounted drilling rigs, is designed for down-the-hole blast hole drilling. Ranger 8002 is a hydraulic, self-propelled, self-contained, crawler-based surface-drilling rig. Axera D07RP, a one boom diesel-hydraulic jumbo drill with high frequency hammer, is used in underground limestone quarry applications. Crawlmaster™ 1208i mobile track unit is a new generation with "i" standing for "intelligence." Tools from the Mission and MG tools product lines include the expanded range of Mission Mirror-Impact-Technology hammers and Trispec road milling tool as well as drill bits, shanks and rods. Visit Booths B-905 and C-7001.

Write In 564 — Or Reply Online

The Screen Machine®, producer of crushing and screening plants for over 37 years, premiers three machines including the 4043T Impact Crusher with a patent-pending curtain relief system design that allows for remote blockage clearance during operation and ease of maintenance and comes with Caterpillar® tracks with high speed travel, a Caterpillar® C-9 300 horsepower engine, 40-inch by 43-inch Horizontal Impact Crusher, 43-inch by 32-inch feed inlet opening, and fully remote controlled operation. The Spyder 516T is a self-contained tracked, portable screening plant with standard Caterpillar® tracks, a 5-foot by 16-foot double-deck screen with Smooth Start™ technology. And the 621T Shredder/Trommel (patent pending) features Caterpillar® tracks, High Speed Shredder Hammermill, 6-foot by 21-foot Trommel. Other products include blenders, wash plants, trammel screens, conveyors, crushers, and 17 screening and shredding plants. Visit Booth C-6429.

Write In 565 — Or Reply Online

A manufacturer of ground penetrating radar (GPR) systems, Sensors & Software Inc. sells and rents a wide range of subsurface imaging products. Noggin® SmartCart™ is an integrated GPR system which can be used to locate subsurface utilities prior to construction or excavation. With real-time display, the Noggin® systems allow fast, accurate data acquisition with results that can be interpreted on the spot. Metallic and non-metallic utilities can be located and accurately positioned to provide a complete picture for subsurface utility mapping (SUE) needs. Data can be printed in the field or downloaded to a PC for post processing and analysis. Visit Booth S-11524.

Write In 566 — Or Reply Online

For improved welding performance in the construction and aggregates industries, Smith Equipment showcases its oxy-fuel welding products and accessories. Of special interest is the Dual Guard Torch series, a new CD-ROM and VHS safety video detailing safety measures and precautions relevant to oxy-fuel equipment and gases, and the company's new cutting and welding toolbox outfits. The Dual Guard Torches are available with 75-, 90- and 180-degree head angles and standard lengths from 17 inches to 48 inches and are covered by Smith's "lifetime" warranty. The 41-minute video, Oxy-Fuel Equipment Operation and Safety, discusses all aspects of oxy-fuel cutting, welding, brazing, and heating safety and features the Dual Guard Torch with its in-head flash arrestor for operator safety. Heavy-duty toolbox outfits provide easy-to-display merchandise for distributors and improves the ability to transport equipment for end-users. Features include high-impact plastic latches; can safely transport oxy-fuel equipment; and are available for both the combination outfit and the hand torch outfits. Visit Booth G-244.

Write In 567 — Or Reply Online

As a manufacturer and distributor of industrial and construction equipment tires and rubber tracks as well as innovation, technology and logistics, Solideal Tire's line includes pneumatic, resilient, and press on tires, wheels and rubber tracks. The Trackmaster OTT Rubber Track and Solideal Agricultural Track are now being introduced. With the Trackmaster, a skid-steer machine can be converted from a wheeled machine to a rubber track machine and provides maximum traction. The Tiger or Leopard Ag tracks will be available mid 2005. Due to its heavy-duty carcass and double angled bar lugs, the Tiger Hi-Profile track will move tractors through the worst conditions and is a solution for high horsepower tractors. And the smooth ride of the Leopard Hi-Mileage track is available for a wide range of machines from tractors to harvesters. Visit Booth G-235.

Write In 568 — Or Reply Online

Super Products Corporation introduces the Quiet Supersucker®, an industrial vacuum loader with a reduced noise level with a sound suppression option. The Quiet Supersucker® was a joint effort between Super Products and Dresser Industries, who manufacture the vacuum pump, and a designer of acoustical enclosures. Visit Booth S-10803.

Write In 570 — Or Reply Online

The Mme 250 Hydraulic Drilling Attachment is designed for use with mini equipment. The attachments use the hydraulic power of the excavator for all drill functions with drilling depths up to 100 feet with diameters up to 4 inches. Applications for the Mme series are foundation repair, retaining walls, blasting, and coring. Visit Booth C-6361.

Write In 571 — Or Reply Online

An array of jaw, cone and impact crushers will be featured including the track-mounted Terex Pegson 650 Premiertrak which utilizes an M Series single-toggle jaw crusher with hydraulic setting adjustment. The feed opening is 26 inches by 44 inches; vibrating grizzly feeder is 14 feet by 3 feet 6 inches; and the 15-foot by 8-foot hydraulic folding feed hopper has up to 13-cubic-yard gross capacity. Standard equipment includes suspended, self-cleaning, overband magnetic separator; dust-suppression sprays; heavy-duty tracks; and Cat 6-cylinder C-9 engine. Track-mounted 1412 Trakpactor impact crusher plant features a Hazemag horizontal AP-PH 1214Q primary impactor with hydraulic controls for uniform products, plus the PLC CAN BUS control system automatically regulates the feed to the crusher, based on engine load. The 1000 SR Maxtrak features the all-in-feed cone crusher with two-deck, 5 feet by 11 feet product sizing screen; input conveyor/hopper; product conveyors; and oversize return conveyor on a single chassis. Visit Booth SL-540.

Write In 484 — Or Reply Online

High-pressure JSC Series pumps designed for pumping operations requiring processing pumping fluid with large solids at a significant flow and pressure, come equipped with cast iron casing, impeller and stress-proof steel shaft. Stainless steel shaft sleeves and a replaceable cast iron wear ring assist in priming the pump. The stainless steel allows pumps to handle caustic and high temperature fluids and can handle solids up to 4 inches in diameter, flows up to 11,000 gallons per minute, heads of 450 feet, and pressure up to 195 pounds per square inch. For industrial, mining or construction applications, Thompson pumps are designed with the Enviroprime® compressor-assisted priming system allowing automatic dry priming, ensuring that no pumped fluid escapes the system and returns into the environment. Available in 3-inch through 16-inch models and impeller diameters (12 inches to 17.5 inches), options include site trailer and control panel with automatic start/stop and float systems for unattended pumping. Visit Booth C-5062.

Write In 572 — Or Reply Online

What started in 1965 as a solution for allowing telephone linemen to perform tasks at varying heights in a safe and dependable manner has grown into a company that serves a multitude of industries. Time Manufacturing displays the CONDOR 170-S with its 170 feet of working height and the CTA-104-I whose short jacking capability allows for the lift to operate over one side of the truck without requiring the operator to fully extend the out and down outriggers on the opposite side. The Versalift VST-6000 articulating, telescoping aerial and VO-40-MHI articulating, material handling aerial will also be on exhibit. Visit Booth G-332.

Write In 574 — Or Reply Online

The Progressive Torque Differential (PTD) is Tractech's new limited slip differential. Under normal road conditions, the PTD performs like an open differential, however, on wet, muddy, icy, or loose terrain, torque is transferred to the wheel with the highest traction. This allows the vehicle to maintain control and continue operating. Suitable for use in construction equipment, trucks, agricultural tractors, and front-end loaders, the PTD works in front axle, rear axle and inter-axle applications. Tractech has produced dependable differentials for construction, agriculture, automotive, and military applications for 60 years. Visit Booth C-4815.

Write In 575 — Or Reply Online

New, Ultra-550 Containment Sump captures spills and leaks from 500- and 550-gallon fuel and oil tanks. Rugged, all polyethylene construction will not rust or corrode and the large, 605-gallon capacity meets Stormwater, SPCC and EPA Containment Regulations. It can be used with an optional Ultra-Self Bailer for outdoor containment which allows stormwater to passively drain from sump while capturing hydrocarbons. UltraTech offers a complete line of spill containment and Stormwater management products to help comply with environmental regulations. Visit Booth S-8953.

Write In 576 — Or Reply Online

New scanning and attachment features facilitate the capture, storage and retrieval of images and documents for online viewing and management. Attaching/indexing documents and images directly to data and reports can save valuable time otherwise spent hunting for paper work and reduces office space consumed by boxes and filing cabinets. Features include an Indexing and Search Retrieval — automatic indexing allows users to search and quickly find documents/images using common data fields such as jobs, equipment, employees, vendors, customers, etc.; Document Routing — scanned images of documents such as AP invoices are easily and electronically routed for review and approval or comments; CD Archival — documents and images can be burned to CDs for archive storage or distribution to others; and Single Image or Batch Scanning captures a single image with a push of the button on the desktop, or a batch of documents can be scanned for efficient high-volume processing. Visit Booth S-17519.

Write In 577 — Or Reply Online

Volvo Construction Equipment (Volvo CE) is in the final development stages of a new 70-ton Volvo hydraulic excavator. Two machines designed for the construction equipment industry will be presented. The new Volvo excavator, engineered in close cooperation with customers from key markets throughout the world, has been designed for a number of different segments including civil engineering, heavy construction, building, and extraction. One excavator with a standard boom and arm as well as one with mass excavation boom and arm will be displayed. Design and engineering focus during development of the new excavator was on high reliability and performance and lowest operating costs. Powered by a Tier 3 Volvo engine using Volvo's new Advanced Combustion technology (V-ACT) system, full-scale production of the 70-ton excavator, the largest in the Volvo CE hydraulic excavator product range, will occur during the last quarter of 2005 for delivery to markets. Visit Booth N-1471.

Write In 293— Or Reply Online

Wirtegn America Inc. introduces Hamm HD 0120V, a roller with an operating weight of 26,345 pounds, drum width of 78 inches, offset working width of 81.5 inches; and working speed of 3.9 miles per hour. The rear drum features oscillation compaction with oscillation force of 46,125 pounds to 62,775 pounds; the front drum features conventional vibration at a frequency of 3,000 vibrations per minute. Model 3412 VIO soil compactor with both vibration and oscillation within the drum will be introduced as well as Wirtgen HT 11 cutting system featuring Rhino cutting bits and holders; Wirtgen 2000 Combo Cutter; FCS L fast-change drum system for W 1900/W 2000; W 2000 recycler/reclaimer; W 50 and W 50 DC mid-sized cold milling machines; Service Training Trailer for Hamm service technician education; and new electric screeds from Vogele America Inc. including the 8-foot front-mounted HF400E; 10-foot, rear-mounted HR500E; and the 2219T paver with AB600TP2 high-density screed. Visit Booth S-500.

Write In 378 — Or Reply Online

A new line of Gannon® 1/16-yard buckets, available as "pin-on" or with a unique new coupler, offers bucket widths ranging from 9 inches to 20 inches, designed for cleanup, excavation or trenching in small spaces. The new coupler's "blank hook" design enables it to attach entirely to the outside of the bucket for full-bucket capacity, making every load more productive. Since the coupler doesn't interfere with the scooped material, it operates more smoothly, and with less friction and wear. The 1/16-yard bucket fits mini-excavators less than 2,500 pounds and small backhoes or backhoe attachments for skid steers and utility tractors. No tools are required to attach the bucket and coupler to virtually any OEM mini-excavator. Visit Booth C-4005.

Write In 578 — Or Reply Online